Dual-in-line package: LTV 1-channel type. LTV 2-channel type. LTV- 4-channel type. * Wide lead spacing package: LTVM: 1-channel type. Tel: Fax: / http://www. Photocoupler. Product Data Sheet. LTV (M, S, S-TA, S-TA1, . Lite-On LTVB: available from 21 distributors. Explore Optoelectronics on Octopart: the fastest source for datasheets, pricing, specs and availability.

Author: Shaktilkree Mir
Country: Tunisia
Language: English (Spanish)
Genre: History
Published (Last): 27 September 2018
Pages: 242
PDF File Size: 17.65 Mb
ePub File Size: 18.36 Mb
ISBN: 650-2-56835-545-6
Downloads: 52228
Price: Free* [*Free Regsitration Required]
Uploader: Voshakar

The fastest computers used bipolar transistors in emitter-coupled logic ECLand even the more garden-variety logic chips that had decent performance were S or AS with Schottky-clamped diodes. On the firmware side, vatasheet were getting concerned, as a deadline was approaching and we still had problems. This all makes a robust high speed ptv817 design an ugly and complex process.

My rule of thumb would be to see how low of a resistance you can go without preventing the transistor from turning on, and then multiply that resistance by something in the range so you have plenty of margin.

Receive a notification when Jason Sachs publishes a new article: It still had some problems, which I finally traced down to a ferrite drum-core inductor. It was a cost-cutting measure on a circuit board that needed to datahseet the current.

If the empty row is between circuit nodes that are sensitive to capacitive coupling like the Miller effect between base and collector of a transistor, or an input node and ltg817 noisy nodetie the row in between to a static voltage e.

LTV817 Datasheet

Previous post by Jason Sachs: Circuit designers typically use a Schottky diode clamp or a technique called the Baker clamp to keep the collector in an NPN transistor just above the saturation voltage. Life gets even more complex when you are heavily current constrained – putting loads of LED current in only helps if its not limited.

Datasheey the semiconductor industry has overwhelmingly datasheef to CMOS, not only for digital logic and microprocessors, but also for analog and power semiconductors, primarily because of its low static power utilization. The second lesson is to make use of pre-existing economies of scale.


Op-amps are optimized to be nice and linear. I got a passable battery charger working in time.

And the deadline was getting closer… so we asked to look at the code itself. Good transistor drive circuits keep all three of these effects in mind, using essentially the following techniques: Foxtrot sent us the first few prototypes. Eventually we got an updated prototype.

If you can get it to work but it costs more than you planned, at least you have a shot at success and can reduce cost in the future.

The exposure of light onto the phototransistor essentially acts in place of the normal base current. The website they put up was very nice but referenced Pease’s “33 year career at TI To post a new comment not a reply to a comment check out the ‘Write a Comment’ tab at the top of the comments. All these things mean that you need to have lots of CTR margin: This capacitance has to be charged up to turn the transistor on, and discharged to turn it off.

Dxtasheet bipolar transistors might have a current gain in the range, and there were all sorts of lfv817 for driving them on and off quickly.

Some boards use thicker copper plating to handle high currents. Good transistor drive circuits keep all three of these effects in mind, using essentially the following techniques:. I had been working about 18 months after graduating college. The third technique listed above, keeping the base-collector junction from saturating, is possible datasheeet use, ltf817 we connect a Schottky diode from base to collector; this keeps the collector from going more than about 0.

Oh, and you get an output enable pin for free. He ltv8177 making things spin. One more quick comment before we do, though:. Without that resistor, the only way for charge to get pulled out of the base is via the base-emitter current, and it takes a while to decay. The second round of prototypes were better, and he sent a few of them to us.


Sachs, all rights reserved. To post reply to a comment, click on the ‘reply’ button attached to each comment. At this point we got Mr. Arduino Robotics Lonnie Honeycutt. Hi Jason, thanks for another great article – I’ve enjoyed all your embedded related articles so far! In fact, if we look at the LTV datasheetwe datashedt see this graph:. Comparators are daatasheet to be fast. Turning datasheeet a transistor in the saturation region requires extra charge to be removed. In a plain transistor circuit as opposed to a phototransistorthe base current would come from a voltage through a resistor, and we could add parallel capacitance to this resistor.

Let that sink in — it was an assembler used to program the PIC16 architecture with completely different instructions. The other techniques would be available to us if we had access to the base terminal. We never saw the first round of prototypes Mr. Comments Write a Comment Select to add a comment [ – ]. Three or four decades ago, if you mentioned transistors, the implication was that you were probably talking about bipolar transistors rather than MOSFETs.

But first I need to go on a short tangent and vent.

But this charger caused enough electromagnetic interference that it disrupted the communications, and it stopped and displayed a fault. A 2N equivalent is fine for Q2.

LTV OPTOISOLATOR 1CH 4-DIP Lite-On Inc datasheet pdf data sheet FREE from

Now the phototransistor will never saturate, so we can move the Schottky clamp to Q2 instead, to prevent it from saturating. Although bipolar transistors will probably be around for a while, I think the techniques of using them are at risk of becoming obscure. Foxtrot was a sub-sub-sub-sub-contractor.

And lucky me, all of us were in different states.